How to Install a Ghost Immobiliser
Ghost immobilisers are hidden security device that protects your vehicle from key cloning and hacking. It works by stopping the engine from starting until a PIN number is entered. This could be as long as 20 characters.
It is unnoticeable by thieves and they are unlikely to be expecting this extra layer of security. Certain systems have an app that allows the owner to deactivate their immobiliser in the event of forgetting their PIN number or utilize the service/valet mode.
Connecting to the vehicle's CAN bus
The Ghost 2 Immobiliser is an advanced security system that can be integrated into your vehicle's ECU offering a secure protection against thieves. It is highly efficient and user-friendly and is a great component of your vehicle's security arsenal. However, like any anti-theft system, it is not impervious to failure and requires regular maintenance to ensure optimal operation. Luckily, this guide will assist you in getting the most benefit from your Ghost 2 Immobiliser.
CAN (Controller Area Network), a robust serial networking that allows microcontrollers to communicate with each other over short distances. A central control unit is not required. It is designed to allow multiplexing of electrical wiring in vehicles to cut down on copper and offers a range of advantages, including low cost and ease of use.
In the majority of modern cars, the CAN protocol is used to connect with a variety of systems, including the engine management system (EMS) steering module, transmission controller air conditioning controls, and more. It also transmits data from sensors including inputs and speed sensors, to control various features of the vehicle. The CAN bus is used to monitor these various components, and prevent the vehicle from starting if they are in danger of failure.
It's crucial to understand how the CAN bus functions and how it is secured. It is possible to add new features to a vehicle using CAN bus, however it's important to secure it from threats from hackers and other types. The best method to achieve this is to install a firewall and monitoring your CAN bus through software.
Ghost2's control unit is concealed in the car's wiring harness or dashboard, removing the possibility of a burglar physically tampering with it. It is also impossible to reset a PIN or an emergency code without access to the vehicle.
If you have to hand over your vehicle to a valet parking service, maintenance, or any other reason, you can turn on the Transport Mode. This option disables the Ghost immobiliser's ignition and keyfob functions, and will only reactivate when the vehicle reaches 31 mph for 15 minutes.
How do you create a PIN code
The Ghost immobiliser is a robust security system that guards your vehicle from theft. The latest technology utilizes an PIN code to disable the engine and prevent it from starting without the proper code or an authorized fob/mobile device. Its discrete design ensures the system is unnoticeable and provides unrivaled protection against theft. Furthermore, the system is TASSA tested and could lead to significant savings on car insurance premiums.
During installation, Ghost enters a "learning mode" to record the sequences of buttons that are pressed to create your unique pin codes. Once the pin code is created the installer will guide you through the process of activating the system. Once activated the Ghost system disables the motor that starts your vehicle unless you enter a valid PIN or switch the vehicle to transport mode. This makes it very difficult for thieves to duplicate or hack your vehicle's starter system.
It is easy to install it is easy to install a Ghost immobiliser, but you must follow the detailed instructions included in the user's manual to ensure the proper operation. Multimeters and hand tools can be used to check electrical values. Insulation tape and heat shrink tubing are a great way to protect exposed wiring and cable ties are essential for keeping everything tidy and secure. Test the system on regular basis to identify any potential issues.
It is crucial to test the system one last time before you turn on the ignition. The Ghost immobiliser will be able to rearm itself after 3 to 30 seconds, based on the vehicle model. The system also has an option for Service/Valet that allows you to temporarily disable the system while you are servicing your vehicle or valet parking.
Ideally, the immobiliser should be placed in a hidden location beneath the steering wheel or dashboard. Make use of a small piece of duct tape or paint on the wires of the CAN H and CAN L to make them easier to locate during testing. The CAN H and L wires must also be connected to an electrical source that can provide an uninterrupted 12V. It is crucial to verify the connections after testing because an the incorrect identification of these wires may cause system malfunction.
Invoking the system
A ghost immobiliser stops your car from starting until you press a few buttons on the vehicle, typically on the steering wheel, the door panel or the central console. The sequence can be changed by the user at any time. Once the system is activated, it is not able to be disabled by thieves, making it a good option for anyone who wishes to protect their vehicle from theft.
The system is designed to be undetectable. This means it can't be detected by modern diagnostics or code-grabbing technologies. It does not emit radio frequency either making it even more difficult for thieves identify.
If the device is located it will stop the engine from starting. It will also sound an alarm to scare the burglar away. The device can be used to track the location of a car and aid in the search for the vehicle in case it was taken.
If you are interested in a ghost immobiliser get in touch with the experts at Car Specalist Customs to get a quote and discuss your options. We are qualified to install ghost immobilisers on your vehicle. We will ensure that it is hidden in a location that is difficult to reach. We can also install other security measures, including the kill switch and wheel lock to keep your vehicle safe from theft.
Disarming the System
It is important to know how to disable a Ghost immobiliser if it is installed on your car. You can use this in case you forget your keys or your car battery dies. ghost 2 immobiliser problems utilizes a unique PIN code, which only you know. It won't be able to start the vehicle without this code. Pressing a combination button on the steering wheel or on the dashboard is the most efficient method of entering your code. This is a simpler method than using the key fob and also stops anyone from copying your remote.
Ghost2 is not intrusive unlike some aftermarket immobilisers which require cutting wires to facilitate installation. It also integrates with the CAN bus system of your vehicle to function. Its most notable feature is its ability bypass the engine without impacting your vehicle's normal functions, making it difficult for thieves to use signal boosters or duplicate your car key. It does not emit radio frequency, so thieves are unable to detect it.
The Ghost system also features the Transport Mode that allows you to temporarily disable the security system for situations such as transportation or servicing. This feature is ideal if you are lending your vehicle out to someone else without sharing your PIN code, or if your vehicle needs to be secured even while you drive it. To activate the Transport Mode you need to press the service button five times within 2 seconds. The Ghost system will confirm activation by giving 5 signal indicators.
Save the emergency code in your vehicle in a secure place. If you are ever locked out of your car You can call the company or technician who installed the system, and they will give you the code. If you are unable to reach them You can always try contacting an authorized dealer, but this will involve verification procedures and could incur additional costs.
Aside from the convenience of this system, you can rely on it to protect your vehicle from theft and help reduce the cost of insurance. Many insurance companies offer lower monthly premiums or even financial incentives to install this anti-theft device.